Iowa Precision Industries Pro-Ductomatic
|
||||
|---|---|---|---|---|
 |
||||
| The Pro-Ductomatic is the basic machine needed for a duct shop, whether used as a stand-alone machine to produce duct blanks or as the heart of a Fabriduct line.
The Pro-Ductomatic has the capacity to remove coil set, bead, and notch for two-piece or wrap duct, and cut off in a feed-to-stop shearing process. There is no minimum cut length or minimum on notch spacing.
PC-based controls ensure consistent quality of leg lengths and feeds. |
||||
Features |
||||
•Coil width capability: 48", 60", and 72" (1200mm), (1500mm), and (1800mm)
•Galvanized or mild steel to 16-gauge •Blank length accuracy +0.020" |
||||
 |
||||
Iowa Precision Industries Pro-Fabriduct
|
||||
 |
||||
| Produces commercial and residential ducting. Modular design with 11 integrated flexible workstations. "U" or "Z" configurations to optimize floor space. Notches vees and corners. Forms pittsburgh, snap-lock, TDC, slip & drive seams and joints. Automated application of glue and insulation. Automated production control with integrated PC. Operator programmable. The controller will store up to 100 programs for easy recall. Modem included for remote factory support. Processes flat sheets, 4-piece duct, "L" duct sections, "U" duct sections and wrap around duct sections |
||||
| |
||||
Iowa Precision Industries Corner-Matic
|
||||
 |
||||
| Corner-Matic
Model CM-C/F-DH automatically inserts corners into both ends at once and crimps them into place. The optional adjustable model accepts 4 to 6-foot sections. |
||||
| |
||||
Iowa Precision Industries Whisperloc Seam Closer
|
||||
 |
||||
| Models FAH-3456 & FAH-1872 are available in the horizontal or vertical and close Pittsburgh seams in 3- to 6-foot duct sections. |
||||
| |
||||
Iowa Precision Industries Ajust-A-Matic Adjustable Elbow Machine
|
||||
 |
||||
| Model AEM345 automatically produces 3", 4" and 5" (76,2-101,6-127 mm) elbows from .013" to .018" (0.33mm to 0,46mm) gauge steel. Model AEM678 produces 6", 7" and 8" (152,4 - 177,8 - 2-3,2mm) elbows from .0125" to .020" (0,31mm to 0,50mm) gauge steel.
Model AEMBM9-16 produces 9" to 16" elbows, and can also be programmed to produce 30 and 60 degree elbows in the same diameters. |
||||
| |
||||
Iowa Precision Industries Tube-A-Matic
|
||||
 |
||||
| Model AEMTM3-16 Tube Fabricating Line |
||||
| |
||||
Iowa Precision Industries Collar-Matic
|
||||
 |
||||
| Iowa Precision's Collar-Matic Line takes the hand work out of collar production for collar/boot assemblies.
The line produces 5,6,7 or 8-in. collars with easy tooling changeovers for each diameter.
The system uses convenient 2 1/8 in. drive cleat coil stock, .013 to .015-in. thick, to form hemmed collars.
An integral parent metal locking joint eliminates the need for collar rivets or staples.
The line's rollformer hems the collar's exposed edge while maintaining the required inside diameter.
Collar-Matic automatically produces and places the collar into the beading die, ready for collar/boot assembly. |
||||
| |
||||
Iowa Precision Industries Colatch
|
||||
 |
||||
| This machine performs the following with foot pedal control:
Expands the boot or take-off, Grooves the collar and boot or take-off,
Stabilizes the collar to boot or take-off. Models "B", "C", and "D" produce 4" through 20" diameters. |
||||
| |
||||
Iowa Precision Industries TDC Wrap Brake
|
||||
 |
||||
| The TDC Wrap Brake is designed to allow a single operator to accurately place and fold flat blanks with TDC rollformed flanges into L-shape or full wrap duct sections. It folds blanks up to 72" (1800mm) and 16-ga. (1.6mm) thick. (Minimum wrap size is 8x8" (200x200mm)).
An on-board PLC controls the clamping and braking sequencing. The clamping beam and folding beam are motorized to perform the adjustable bend angle from 1° to 90°. Safety interlocks keep the system safe. |
||||
| |
||||
Iowa Precision Industries Plasma Coil Feed
|
||||
 |
||||
| The Plasma Coil Feed machine feeds coil stock to Plasma Cutting Machines. It incorporates drop-in style uncoilers, straightening rolls to remove coil set, and pinch rolls to feed the 16-gauge (1.5mm) maximum thick material. |
||||
| |
||||
Home • Rollforming • Snap Lock • Duct Connector • TDC Machines • Power Notching • Round/Oval • Accessory
Plasma • Special Rollforming • Waterjet • Clinching • Blanking • HVAC • Contact • Search • About
©2006 MK Machinery & Supply